Secure Checkout
Free Shipping On Qualifying Orders Over $250!
Your Shopping Cart Is Empty

Secure Checkout

SKU: R1627 Jeep Wrangler JK, Fully Welded Tie Rod

Jeep Wrangler JK, Fully Welded Tie Rod
Click image to zoom
Purchase Jeep Wrangler JK, Fully Welded Tie Rod
  • Jeep Wrangler JK, Fully Welded Tie Rod

  • ★★★★★ ★★★★★ 14 reviews
  • Part Number: R1627
  • Shipping Weight: 22.00 pounds

  • $217.95

Jeep Wrangler JK, Fully Welded Tie Rod

Jeep JK Specific Off Set Tie Rod!! Fits 2007-2017 Jeep JK fully welded. Heavy Duty and a great addition for your vehicle! This kit Includes a fully welded Tie rod with hex head tube adapters, and Offset GM 1 ton TRE's (1LH & 1 RH). Tie rod is made of 1.5" x .25" thick DOM Steel tube pre fit for the JK Axles.

This kit will work on 17" wheels with a maximum 3.75 Backspacing. May not fit 17"inch factory wheels. It will NOT fit your factory steering stabilizer bracket! You may have to ream your knuckle's taper (depending on which knuckle you use) to accept the GM 1 ton TRE but the end result is more than worth the effort! Some aftermarket and factory wheels with deep backspacing could make contact with tie rod ends. It is the owners responsibility to be aware of changes to vehicle performance and handling characteristics.

  • CHECK FITMENT OF WHEELS-TIRES PRIOR TO INSTALLATION. COMES PROFESSIONALLY WELDED!

You will receive:

Additional Products you may need when installing this kit:

Write Review
★★★★★ ★★★★★
5.00/5 Stars out of 14 Reviews
5
14
4
0
3
0
2
0
1
0
Pages 1   2   3
So far so good!
5
Beren Boyd (Bardstown) | July 1st, 2022
Definitely a big upgrade from the factory tie rod. Extremely easy to install and very easy to adjust. Highly recommend this product.
Beefy
5
Cory (GA) | January 24th, 2021
This is a beefy tie rod, love the adjustments on both ends. I was hesitant to use the tapered inserts but they worked great and fit perfect with this tie rod. I did pre drill with 3/4 bit before stepping up to 7/8.
Verified Buyer
Nice track bar
5
Tim Robinson (Valdosta, GA, US) | May 13th, 2020
Installed this beauty under my Jeep and it looks amazing. Only gripe is One of the bungs must have been welded HOT because it was fairly difficult to thread in one of the TREs. Had to run a tap down to clean up the threads. Installed the complete steering setup for my Jeep and it is nice and firm. Thanks RuffStuff!
Verified Buyer
1 ton tie rod
5
Tim Perkins (Richmond, KY, US) | May 14th, 2019
After doing some search, I decided to go with the Ruffstuff tie rod. Install went easy. Even drilling out the knuckles was not that bad. Got everything on and it drives great. Have wheeled it three or four times and everything is holding up great. I would recommend this to anyone. My only complaint is the boot on the tie rod. It just sits on there. Looks like it will let the grease leak out. Even though it has been on for 4 thousand miles and no leak. I just don’t care for the design.
Verified Buyer
Stout!!!
5
John E Munder (Wylie, TX, US) | February 21st, 2018
Just received this from the brown truck today. Man this thing is pretty hard core! 1.5 X .25 DOM not much more to say. Doubt I could bend it wheeling and probably the last tie rod I will ever need on this particular Jeep. TREs are nice and HD also. Not much more to say...buy it! Or be a dumbass and spend a lot more money on something inferior.
  • GM Tapered Knuckle Insert On Jeep JK Axle

Questions & Answers

Ask a question

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Rate Product